SAPSONS HYDRAULIC CABLE SPIKING TOOL is specially designed to ensure the absence of voltage in low voltage and Medium voltage power cables before undertaking any electrical maintenance work. Human life is precious and by using our Cable spiking tool, the safety of the Electrical team is ensured. They can simply check the Power cable and eliminate accident. What is cable Spiking tools? Cable Spiking tool is one of the Safety tools used to protect the Electrical workers from any Electrical accident while carrying out cable repair, maintenance, jointing or end termination etc... The cable spiking chisel pierces the sheath of the cable, as well as its insulation, to reach the main conductor. If the cable is powered prior to cutting, an arcing fault is caused by breaking down the insulation. Why are spike tool used? Cable spiking tool is used to ensure that the power cable under maintenance is not live. Cables are spiked with the help of Cable spiking tool and confirm the circuit is not Live. It is one of the very important safety procedure universally followed and the Cables are preliminarily spiked before carrying out jointing or terminating of faulty 11kV/33kV cables. Our Cable spiking tool is intended to prove that any power cable under maintenance is previously disconnected, is dead before starting the work, when these cables are undergoing repair, diversion or maintenance. The design of SAPSONS cable spiking tool is robust and reliable which consist of a hand operated hydraulic pump connected by a hydraulic hose to the hydraulic cylinder. The Cable Spiking chisel which is made of special alloy steel and hardened is connected to the piston of the Hydraulic cylinder. When the cylinder is operated thru the Hydraulic hand pump, the chisel pierce into the cable to reach the conductor. The Cylinder is mounted on a Rectangular shaped tubular steel body which is placed on cable dia and locked with the lower base clamp by threaded steel rods on both the side. A separate earthing cable of approx. 6 mtrs. long crimped at one end with suitable lugs connected with the tool and the other end is having the earthing rod for grounding.

FEATURES & APPLICATIONS : • Used to cut conductors up to 40 MM DIA • Operation similar to a hydraulic jack • Knob-handle is turned to enable lineman to operate pump handle • When cut is completed, knob is turned in opposite direction to allow cutting head to open • Epoxiglass pole, handle and hydraulic hose have been tested upto 700 bar working pressure. • Hydraulic oil grade 68 is used in Hand pump. • Hose has a minimum burst strength of 15,000 PSI • Features include jaws designed to cut without flattening conductor. • Jaws are made out of special alloy steel for long and trouble free application • Well balanced, requiring minimum effort to cut large conductors.

Tube Wall Reducers are specialized tools used in metal forming, pipe manufacturing, and fabrication to reduce the wall thickness of tubes or pipes without changing their outer diameter significantly. These tools are essential in applications requiring precise material thickness for structural, fluid transport, or pressure-based functions. Tube Size: 3/8' - 4' (9.5 - 101.6 mm) OD

Effective cleaning of Tube Inner dia results into longer life and better performance of the vessels and Equipments. Tube cleaning brushes are used for soft , light scales inside the tubes. Bristles are made out of Nylon, steel and Stainless steel wires, as per customer requirements. Can be easily connect and disconnected thru threaded coupling. Available From 3/8” To 4” OD Tubes. TYPE : Condenser Brushes, Turk Head Brushes And Double Spiral Brushes, Etc.

Condenser Tube Cleaner Kit is Pneumatic operated system, designed to clean straight tubes in Heat Exchangers, condensers, coolers, chillers etc. These equipment contain many small diameter tubes which vary from 3/8" to 1.1/4" in diameter and six to twenty feet or even more in length. Consists of Portable Pneumatic Drive, Water Flushing Attachment, Set Of Hollow Shafts and Couplings, Cleaning Heads Like Drill, Cutter and Brush along with air and Water Hoses, all supplied in suitable steel carrying case. The suitable cleaning head according to the tube ID, is connected thru thread in to the hollow shafts , which is again connected to the Pneumatic drive, and inserted into the tube. Number of shafts are connected thru couplings to increase the length , to cover the entire length of the tube, to be cleaned. A water flushing system is also attached to the drive to flush out the loose deposits out of the tube as well to keep the tool head cool. The Pneumatic drive runs at a speed of about 700 RPM , along with the water flow, and the tool head breaks the scale, while the water loosens the deposits. Very Handy and user friendly, this equipment is very useful to those Industries, where periodical cleaning of tubes are mandatory.

It is a Shaft consist of Inner Core ,Outer casing Motor Coupling and Hand piece. It is designed to penetrate in to the tube inner dia, flexibly even into the bend tubes, without damaging the inner surface of the tube, and capable of transmitting rotary power from the Power unit to the tool head or brush. INNER WIRE CORE is flexible shaft's most important working element. It is designed and constructed to meet power drive operating conditions that include torque, speed, length and minimum bend radius. At the centre of the core is a single wire around which successive multi-stranded layers of wires are wrapped. Each layer is wound in the opposite direction and at right angles to the layer directly beneath it. The direction in which the wire on the outer most layer is wound determines the direction in which the shaft is designed to rotate. OUTER CASTING made of galvanized steel strip and is internally reinforced with antifriction lining to support the wire core and resist the torque. Outer casing does not rotate but protect the inner core and the tube inner dia. HANDPIECE is attached to one end of the shaft, either detachable or fixed type, with threaded spindle to connect tool heads or brushes. MOTOR COUPLING is fitted to the other end of the shaft, either threaded type or shear pin type, connected to the main power unit. Available in 25mm(1”) , 32mm(1.1/4”) and 36mm(1.3/8”) OD with 12mm(1/2”),16mm (5/16”) and 19 mm(3/4”) inner core respectively, with various length of 6 to 22 mtrs. Long. Longer length is also available on request.

Periodic cleaning of Tube Inner dia in Processing Equipment like BOILERS, Air Heaters , Evaporators and Sugar Refining vessels is very essential for its better performance and longer life. Our Flexible Shaft Machines are designed to meet customer’s expectation, with rugged construction, simple to operate, minimum maintenance and trouble free service. It is a self-contained portable unit, fitted with lifting or carrying handle. It consists of a TEFC, continuously rated, squirrel cage, 440 volts, 3 phase, 50 C/S, AC electric motor. Standard machines are available with 3, 5 & 7.5 HP and Free speed of 2880 or 1440 RPM. It is controlled by a push button starter, with features like single phase protection, overload and under voltage protection. In addition it is also ambient temperature compensated. Each machine is fully wired, carefully tested and is supplied with a 20 feet long power cable .

Sapsons hydrostatic pressure testing pumps & equipment are the perfect diagnostic solution used to check for leaks or defects in tubes, valves, pipes, hoses, boilers and pressure vessels, castings, components, etc. by filling them with water. They are designed and manufactured to handle flow rate ranging from 12 lpm to 445 lpm and pressure ranging from 70 bar (1000 PSI) to 1400 bar (20000 PSI). They are either manual or electric/pneumatic motor driven. They consist of : - Positive displacement reciprocating plunger - Safety relief valve and associated controls - Pressure gauge"

1300 Series is the long reach expander used for higher thickness tube sheets, where expansion lengths is longer. Used for oil Coolers , Radiators & other equipment, where small diameter tubes are used. Suitable for Tube sizes ¼” to 3/8” OD. For Tubes of I.D. : 0.231" (5.8mm) to 0.331" (8.4mm). Available in Roller Lengths of 3/4" (19.05mm) and 1.14" (31.75mm) for Tube Expansion Length 3/4" (19.05mm) to 3.1/2" (88.9mm)