Ratchet Wrench : A ratchet wrench is a hand tool used to tighten or loosen nuts and bolts efficiently without having to lift and reposition the tool after each turn. It features a ratcheting mechanism that allows the handle to move back and forth while the socket stays engaged with the fastener. Sizes: 3/8' to 1/2' square drive with maximum torque capacity of approximately 120 Nm.

HP series : slim-type hand-operated hydraulic crimping tools are designed for hexagonal crimping of aluminum/copper lugs as well as ferrules, and come with a built-in hydraulic pump. Supplied in a specially molded plastic carrying case, these crimping tools are lightweight, portable and easy to use, making them ideal for electrical maintenance engineers and contractors. Size: 10 sq. mm to 300 sq. mm

‘HJ’ Series : Hydraulic Crimping Tools are made out of Solid Special Alloy Steel, where weight is not an issue to the customer, and it is mainly used in manufacturing plants, with Crane facility. These tools are Economy model but heavy in design. HJ Series Hydraulic Crimping Tools are available for crimping Copper and Aluminum Cable terminal ends up to 400 Sq.mm with Ring or Hex dies. Construction and Working: The Crimping Jack and Hydraulic Pump are connected with 2 Mtrs. long Hydraulic Hose pipe and the Hydraulic Hand pump is designed to develop Pressure of up to 250 Kg/ Sq.mm. The mechanism within the pump controls the pressure developed, while crimping and safety valve prevents overloading.

MH Series Electric Power Operated Hydraulic Crimping tools are available with 230 V as well as 110 V Single Phase power supply. The MH Series Hydraulic Crimping Tools are easy to carry and have compact power pack fitted with lifting handle. The MH Series Hydraulic Crimping Tools are supplied with all Aluminum body Motor for less weight and easy portability. Supplied with hand held slim design light weight crimping head, hexagonal dies, and suitable 2 meters long hydraulic hose. Electric Pumps are designed to develop Max. working Pressure up to 700 Bar. The crimping Head is Slim in design and made from Solid Special Alloy Steel to withstand the pressure developed while crimping. Available Models: * SAP-MH-400 – Capacity: 50.0 To 400.0 Sq. Mm (Supplied With Sets Of 9 Sizes Of Dies) * SAP-MH-630 – Capacity: 240.0 To 630.0 Sq. Mm (Supplied With Sets Of 5 Sizes Of Dies) * SAP-MH-1000 – Capacity: 500.0 TO 1000.0 Sq. Mm (Supplied With Sets Of 4 Sizes Of Dies) * SAP-MH-1200 – Capacity: 500.0 To 1200.0 Sq. Mm (Supplied With Sets Of 5 Sizes Of Dies) * Special Model Can Be Supplied With Additional Dies, As Per Customer’s Need. * Extra Long Hose Can Be Supplied With Tool On Request, At Extra Cost. Technical Specifications: Power Supply: 230 Volts Or 110 Volts Single Phase Tank Capacity: 10 Liters Max Working Pressure: 700 Kg/Sq.Cm Motor: 1 HP Pump: 2 LPM For special applications, with high power crimping, we have our HDX and HDZ series Crimping heads, which can be used with both Hand pump as well as Electric pumps, developing up to Max.Working pressure of 700 Bar.

SAPSONS ‘FT’ Series Foot operated Hydraulic Crimping Tools are one of our Unique design, supplied with Heavy duty Foot operated Pump - with sturdiest design, fitted over Heavy steel frame, for well-balanced operation. These are suitable for crimping Copper and Aluminium Cable terminal ends and in-line Connectors upto 1200 Sq.mm. Our FT Series Hydraulic Crimping Tools are equipped with in-built Safety release valve, to prevent the overloading, thus protecting both Pump & Crimping Head. Available Models: * SAP-FT-400 – Capacity: 50.0 To 400.0 Sq. Mm (Supplied With Set Of 9 Sizes Of Dies) * SAP-FT-630 – Capacity: 240.0 To 630.0 Sq. Mm (Supplied With Set Of 5 Sizes Of Dies) * SAP-FT-1000 – Capacity: 500.0 To 1000.0 Sq. Mm (Supplied With Set Of 4 Sizes Of Dies) * SAP-FT-1200 – Capacity: 500.0 To 1200.0 Sq. Mm (Supplied With Set Of 5 Sizes Of Dies) * Special Model Can Be Supplied With Additional Dies, As Per Customer’s Need. * Extra Long Hose Can Be Supplied With Tool On Request, At Extra Cost. The FT Series Hydraulic Crimping Tools that we provide are suitable for any heavy duty crimping applications, to be done at ground positions. Hydraulic crimping head is slim in Design, suitable for easy accessibility inside the panels and confined areas, where other tools cannot be used. Available Models: * SAP-FT-400 – Capacity: 50.0 To 400.0 Sq. Mm (Supplied With Set Of 9 Sizes Of Dies) * SAP-FT-630 – Capacity: 240.0 To 630.0 Sq. Mm (Supplied With Set Of 5 Sizes Of Dies) * SAP-FT-1000 – Capacity: 500.0 To 1000.0 Sq. Mm (Supplied With Set Of 4 Sizes Of Dies) * SAP-FT-1200 – Capacity: 500.0 To 1200.0 Sq. Mm (Supplied With Set Of 5 Sizes Of Dies) * Special Model Can Be Supplied With Additional Dies, As Per Customer’s Need. * Extra Long Hose Can Be Supplied With Tool On Request, At Extra Cost.

SAPSONS ‘HD’ Series Hydraulic Crimping Tools is designed for crimping with Ring or Hex dies to crimp Copper / Aluminium Cable terminal ends/ Ferrules upto 1200 Sq. mm, powered by Heavy duty powerful Hand Pump. The Crimping Head and Hydraulic Hand Pump is connected with 2 Mtr. long Hydraulic Hose pipe and the Hydraulic Hand pump is designed to develop Pressure from 300 to 700 Bar. The crimping Head is Slim in design and made from Solid Special Alloy Steel to withstand the pressure developed while crimping. The mechanism within the pump controls the pressure developed, while crimping and safety valve prevents overloading. This Slim type Hand held Hydraulic crimping head is suitable for Heavy duty crimping and can be easily used inside the panels, very confined areas, critical positions and very critical applications. Available Models: * SAP-HD-400 – Capacity: 50.0 To 400.0 Sq. Mm (Supplied With Sets Of 9 Sizes Of Dies) * SAP-HD-630 – Capacity: 240.0 To 630.0 Sq. Mm (Supplied With Sets Of 5 Sizes Of Dies) * SAP-HD-1000 – Capacity: 500.0 To 1000.0 Sq. Mm (Supplied With Sets Of 4 Sizes Of Dies) * SAP-HD-1200 – Capacity: 500.0 To 1200.0 Sq. Mm (Supplied With Sets Of 5 Sizes Of Dies) * Special Model Can Be Supplied With Additional Dies, As Per Customer’s Need. * Extra Long Hose Can Be Supplied With Tool On Request, At Extra Cost.

Effective cleaning of Tube Inner dia results into longer life and better performance of the vessels and Equipments. Tube cleaning brushes are used for soft , light scales inside the tubes. Bristles are made out of Nylon, steel and Stainless steel wires, as per customer requirements. Can be easily connect and disconnected thru threaded coupling. Available From 3/8” To 4” OD Tubes. TYPE : Condenser Brushes, Turk Head Brushes And Double Spiral Brushes, Etc.

Condenser Tube Cleaner Kit is Pneumatic operated system, designed to clean straight tubes in Heat Exchangers, condensers, coolers, chillers etc. These equipment contain many small diameter tubes which vary from 3/8" to 1.1/4" in diameter and six to twenty feet or even more in length. Consists of Portable Pneumatic Drive, Water Flushing Attachment, Set Of Hollow Shafts and Couplings, Cleaning Heads Like Drill, Cutter and Brush along with air and Water Hoses, all supplied in suitable steel carrying case. The suitable cleaning head according to the tube ID, is connected thru thread in to the hollow shafts , which is again connected to the Pneumatic drive, and inserted into the tube. Number of shafts are connected thru couplings to increase the length , to cover the entire length of the tube, to be cleaned. A water flushing system is also attached to the drive to flush out the loose deposits out of the tube as well to keep the tool head cool. The Pneumatic drive runs at a speed of about 700 RPM , along with the water flow, and the tool head breaks the scale, while the water loosens the deposits. Very Handy and user friendly, this equipment is very useful to those Industries, where periodical cleaning of tubes are mandatory.

Tool Heads is fitted to the Flexible shaft to remove scale and hard deposits from inside the tubes of Processing Equipment. Available in Fixed type with Three and Spring type with 15 Sharp revolving Cutters, it chip the scale at high speed and the resultant centrifugal force. All parts are manufactured from special Alloy steel and heat treated for longer life. For Medium Size Straight Tubes: * PAD Type Arrowhead Drill For Opening Blocked Tubes * PBT Type Boring Tool For Cleaning Semi blocked * PSL Type Spring Loaded For Hard And Obstinate Scale * PDH Type Double Head For Hard And Medium Scale * PAD/UJ Type Drill Head With Universal Joint For Thick Scale * PPA Type Pivoted Arm For Uneven Hard Scale * PSF Type Swing Frame For All Types Of Scale * PSH Type Single Head For Hard And Medium Scale * WBA Type Cup Shaped For Scouring Of Thin Hard Scale * PTH Type Turk's Head For Scouring After Descaling * PDS Type Double Spiral For Scouring Carbon Scale * PGP Type General Purpose For Debarring Polishing Etc.

It is a Shaft consist of Inner Core ,Outer casing Motor Coupling and Hand piece. It is designed to penetrate in to the tube inner dia, flexibly even into the bend tubes, without damaging the inner surface of the tube, and capable of transmitting rotary power from the Power unit to the tool head or brush. INNER WIRE CORE is flexible shaft's most important working element. It is designed and constructed to meet power drive operating conditions that include torque, speed, length and minimum bend radius. At the centre of the core is a single wire around which successive multi-stranded layers of wires are wrapped. Each layer is wound in the opposite direction and at right angles to the layer directly beneath it. The direction in which the wire on the outer most layer is wound determines the direction in which the shaft is designed to rotate. OUTER CASTING made of galvanized steel strip and is internally reinforced with antifriction lining to support the wire core and resist the torque. Outer casing does not rotate but protect the inner core and the tube inner dia. HANDPIECE is attached to one end of the shaft, either detachable or fixed type, with threaded spindle to connect tool heads or brushes. MOTOR COUPLING is fitted to the other end of the shaft, either threaded type or shear pin type, connected to the main power unit. Available in 25mm(1”) , 32mm(1.1/4”) and 36mm(1.3/8”) OD with 12mm(1/2”),16mm (5/16”) and 19 mm(3/4”) inner core respectively, with various length of 6 to 22 mtrs. Long. Longer length is also available on request.

Periodic cleaning of Tube Inner dia in Processing Equipment like BOILERS, Air Heaters , Evaporators and Sugar Refining vessels is very essential for its better performance and longer life. Our Flexible Shaft Machines are designed to meet customer’s expectation, with rugged construction, simple to operate, minimum maintenance and trouble free service. It is a self-contained portable unit, fitted with lifting or carrying handle. It consists of a TEFC, continuously rated, squirrel cage, 440 volts, 3 phase, 50 C/S, AC electric motor. Standard machines are available with 3, 5 & 7.5 HP and Free speed of 2880 or 1440 RPM. It is controlled by a push button starter, with features like single phase protection, overload and under voltage protection. In addition it is also ambient temperature compensated. Each machine is fully wired, carefully tested and is supplied with a 20 feet long power cable .

Flaring of projected tube ends, after Expansion ensures better grip of the tube with the Tube sheet. It can be used either manually or with Pneumatic Chipping Hammer. Made out of Special Alloy and heat treated , to withstand the impact load, while using. Handle portion is knurled for better grip. Available For Any Tube Size Between ½” To 1.1/2” OD Tubes